Precision Tools

• Hardened and Ground steel body
• Spring Tension Knurled nut for easy depth measurement and locking.
• Fitted with stainless steel Rule graduated 64th on one side and 0.5 mm on reverse
• Rule measures 7/32" (5.5 mm) wide and .041" (1.05 mm) thick.

• Handy device for checking radii of tools and dies easier and faster.
• Gage features leaves for measuring both concave and convex radii.
• Each leaf is clearly stamped with the radius size.
• RG-2253 Features Blades locked with 2 Screw (Not illustrated)

Specifications:

• High quality thick Dividers.
• Square legs for balance and grip.
• Hardened and Ground Points.
• Manufactured with Rivet or Screw Hinge.

• Made of Finest quality ground steel with heavy thick stock.
• Blade is hardened and Ground for straightness and Parallelism.
• Squares are accurate both inside and outside
• Sizes 18" (450mm) and above are supplied in finished wooden box.
• Effective Blade length measured from inner edge of the beam to end of the blade and is approximately 1/4" (6mm) more than sizes shown.

• Very handy gauge to quickly determine the Pitch of Various threads.
• Made of High Quality Polished Tool Steel.
• Features a Locking Device at both ends to securely lock the leaves.
• All leaves clearly marked with size.
• Comes in a plastic Pouch.

• For twist drills with acute angle of 118° upto 2" (50 mm) diameter.
• Made from Stainless Steel.

• Rules manufactured from stainless steel.
• Flexible Rules have permanently engraved graduation on front and Conversion table etched on the back.
• Pocket Rules are provided with clip for convenience as well as dual use as a depth gage.
• Flexible Inch alone are graduated 32nd on one side and 64th on the opposite side
• Flexible Inch / Metric rules are graduated 16th , 32nd and 64th on one side and 0.5 and 1 mm on the opposite side.
• Flexible Metric alone are graduated 0.5 mm on one side and 1 mm on the opposite side.

Wiggler and Centre Finder This useful wiggler center finder set comes with 4 interchangeable probes for finding centers, edges, and indicating. Each probe snaps into the body without removing the collet nut. Suitable for use on drill presses, lathes, milling machines, borers etc.. Set Includes:1 x Collet Body with 10mm Shank1 x Ball Contact - 0.250" Ball1 x Disc Contact - 0.100" Disc1 x Needle Point1 x Universal Indicator Holder, M5x0.5mm Thread Mounting

• Sturdy construction surface gage.
• Consists of Adjusting knob and hardened scriber.
• Round base made of close grain Cast Iron.
• Very useful for every workshop.

• Firm Joint to adjust tension as desired.
• Legs machined to rigid length and balance.

• Basic tool for machinist and toolmakers for accurately scribing lines, transferring measurements and probing during inspection work.
• Polished and hardened Steel base with double ended scriber.
• Bottom V. Grooved for Cylindrical work.
• Front Recessed for depressing Spindle below base level.
• Has fine Adjustment for precise angular movement.
• Base has 2 retractable Pins to set against edge of a Surface plate.
• 1/4" (6.35 mm) hole drilled on adjustment knob for positioning a dial indicator.

• Made from Polished stainless steel.
• Double graduation from 0 - 180° in opposite direction.
• Rectangular head protractor provides four convenient working edges.
• Used to draw radial lines, setting Bevels and transferring angles.

• Graduated from 0 - 180°
• Spring Tension nut to secure rule to desired depth and angle.
• Narrow 6" (150mm) rule graduated 64th on one side and 0.5 mm at reverse.

• Made from Ground Stainless Steel.
• Clearly etched Graduation.
• Used for ganging thread profiles 47-1/2° British Association, 14-1/2° Acme, 60° American and metric, 55° whit worth and BSF.

Specifications:

• Handy Gauge for measuring cylindrical bores, bearing work and for gaging slots.
• Made from matt finished stainless steel.
• Clearly etched both sides graduations for precise measurement.

• Popular gauge for ganging Iron Wire, hot and cold rolled sheet steel.
• Made from bright finished and polished hardened stainless steel.
• Gauges have a convenient decimal equivalents of each number.
• Clear permanently etched graduations in English Standard.

Specifications:

• 8PC Parallel Set for Milling and Drilling.
• Two 1/4" holes are provided on each parallel for mounting.
• Use for setting work pieces for needed height in Vise Jaws in seconds.
• Made of Hardened and ground tool steel.

Specifications:

• Very Handy Gauge used in grinding and setting screw cutting tools.
• Made of tempered stainless steel.
• Clearly etched Scale for finding number of threads per Inch through graduations in 14ths, 20ths, 24ths and 32ths of an inch.
• Gauge also features a table of double depth of thread for determining size of tap drills.

• Used in layout works for locating and testing centers.
• Properly shaped and finished legs.

• Multi-Use : Holds both Square and Round Work.
• Stepped Groove Construction permits both Low and High Clamping
• Side Hole-Provided in each block to facilitate clamping.
• Made of Hardened Tool Steel, Machined and Ground in Pairs.
• All Sides Precision Ground Parallel and Square to an accuracy of 0.0003".
• Supplied in 'Pairs' with two Clamps.
• Capacity : 2" (50 mm) Round and 1-7/16" (36.5 mm) Square.

• All sides are Ground Square and Parallel to each other.
• V's are central, Parallel and square and are matched in Pairs.
• Made of Properly Heat treated and Hardened Tool Steel.
• Precision Made for Machinist's and Toolmakers use.
• Supplied in Pairs with two Clamps.

Specifications:

• Ultimate V-Block for Grinding, Milling or Drilling work.
• Made of hardened and Precision ground tool steel.
• The sides are parallel and vee is central and ground.
• Central Hole is provided for Drilling or removing Pins.
• Clamp is smaller than outside width of the V-Block and has adjustable side screw for support.
• Block is provided with black oxidized clamp.

• Made from seasoned closed grained cast Iron.
• Universal V-Block consisting of Four different size grooves.
• Supplied in Pairs

• Made of High Quality Seasoned Castings.
• Blocks are accurately Machined Square 

Specifications:

• Compact and Versatile Comparator Stand
• Rugged Enamelled Cast Iron base.
• Rust Proof chrome plated Pillar at right angle to the base.
• Hardened and Precise ground Anvil
• Provided with fine Adjustment Knob for Zero Setting.
• Suitable for all dial gages including 3/8" and 5/16" dia stem.
• Base Dimension : 6" x 4" (150 x 100mm).
• Pillar diameter : 1" (25.4 mm).
• Supplied without Dial Gage.

• Body and rolls made of Hardened and Precise ground Tool Steel.
• Perfect tool for angular inspection and measurement.
• Top parallel to bottom of rolls ± .0004".
• Distance between centre of rolls ± .0004"

• Single Clamping action stand to hold and set micrometer at various angles.
• Chrome Plated clamping 'C' and black oxidized clamping Screw with cross knurled handle.
• Suitable for Digital and mechanical micrometers.
• Maximum possible involvement is 180°.
• Enameled Stand with Cast Iron base.

• Made from High quality Casting.
• Castings are properly seasoned to avoid distortion.
• Precision ground sides and Ends.
• Flatness and Squareness within .002" Per 6" for Machined finish and .001" per 6" for Ground finish.

• Made of high Quality Seasoned Castings.
• Accurately machined 90° Square.
• Available both in open End and Webbed End Styles

• Made from special tool steel
• Completely hardened and ground
• Tapped holes for clamping jobs in any position
• Stepped design
• Flatness & squareness within 0.002" per 6"

• Used for fixture component and checking Squareness and Parallelism.
• Side ends and faces are finished Square and Parallel within .002" per 6"

• Hardened and Centerless ground to Precision tolerance.
• Locate working edges like shoulders, centering Points and Scribed lines easily & accurately.
• Time saving Positioning tool for Jig Borers and other machines.